DIGICOM SPA RAFFAELLO 14.4 Card Type Modem Chip Set Unidentified I/O Options RJ-11 line, 25-pin serial port, power Maximum Modem Rate 28.8Kbps Maximum Fax Rate 14.4Kbps Data Modulation Protocol Bell 103A/212A ITU-T V.21, V.22, V.22bis,V.23, V.32, V.32bis Fax Modulation Protocol V.17, V.29, V.27ter, V.21 CH2 Error Correction/Compression MNP5, MNP10, V.42, V.42bis Fax Class Class I & II Data Bus External [Image] CONNECTIONS Function Label Function Label RJ-11 line CN1 Power CN3 25-pin serial port CN2 Power switch SW1 DIAGNOSTIC LED(S) LED Color Status Condition PWR Unidentified On Power is on PWR Unidentified Off Power is off DTR Unidentified On Computer is ready DTR Unidentified Off Computer is not ready SD Unidentified On Modem is transmitting data SD Unidentified Off Modem is not transmitting data RD Unidentified On Modem is receiving data RD Unidentified Off Modem is not receiving data DCD Unidentified On Network connection established DCD Unidentified Off Network connection not established OH Unidentified On Modem is off hook OH Unidentified Off Modem is on hook SUPPORTED COMMAND SET Basic AT Commands AT, A/ A, B, E, H, L, M, O, Q, V, W, X, Y, Z &C, &P, &T, &V, &W, &Y, &Z Extended AT commands \A, \B, \G, \K, \L, \N, \W %C, %E, %L S Registers S0, S1, S2, S3, S4, S5, S6 ,S7, S8, S9, S10, S12, S18, S25, S26, S30, S32, S33, S95 Special commands -K, )M Note: See MHI Help File for full command documentation. PROPRIETARY AT COMMAND SET AUTO-MODE DETECTION Type: Configuration Format: AT [cmds] Nn [cmds] Description: Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed. Command Function N1 Handshake at highest compatible rate N2 Handshake at digital interface rate DATA SET READY (DSR) Type: Configuration Format: AT [cmds] &Sn [cmds] Description: Selects DSR options Command Function &S0 DSR forced high &S1 DSR high only while modem is handshaking or connected DATA TERMINAL READY (DTR) Type: Configuration Format: AT [cmds] &Dn [cmds] Description: Selects modem response to DTR Command Function &D0 DTR override &D1 DTR toggle causes online command mode &D2 Normal DTR operations &D3 Resets on receipt of DTR DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials telephone number according to any modifiers included in the string Note: Any combination of modifiers can be used to produce the desired dial functions in sequence. Command Function DL Re-dial last number DP Pulse dialing enabled DS=n Dial stored telephone number n DT Tone dialing enabled DW Dialing resumed following dial tone detection D, Dialing paused D@ Wait for Quiet Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by 5 seconds of silence. D; Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. D! Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. FACTORY DEFAULT PROFILE Type: Configuration Format: AT [cmds] &F [cmds] Description: Sets values in active profile to values found in the default profile Command Function &F0 Factory default profile 0 &F1 Factory default profile 1 FLOW CONTROL Type: Configuration Format: AT [cmds] &Kn [cmds] Description: Enables flow control options Command Function &K0 Flow control disabled &K3 RTS/CTS flow control enabled &K4 XON/XOFF flow control enabled &K5 Transparent XON/XOFF flow control enabled &K6 Unidirectional XON/XOFF flow control enabled GUARD TONE Type: Configuration Format: AT [cmds] &Gn [cmds] Description: Commands the modem to transmit a guard tone in V.22/V.22bis Command Function &G0 Guard tone disabled &G2 1800Hz guard tone enabled MODULATION Type: Configuration Format: AT [cmds] Fn [cmds] Description: Selects modulation format for V.32bis modem Command Function F0 Autoscan from 14400bps (V.32bis) to 300bps (V.21) F1 300bps (V.21 or Bell 212A) F2 1200/75bps (V.23) in originate mode, 75/1200 in answer mode F3 1200bps (V.22 or Bell 212A) F4 2400bps (V.22bis) F5 4800bps (V.32 or V32bis) F6 7200bps (V.32bis) F7 9600bps (V.32 or V32bis) F8 12000bps (V.32bis) F9 14400bps (V.32bis) REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I0 Reports product name I1 Reports firmware release I2 Reports memory test I3 Reports product name I4 Reports firmware release I5 Reports active Country Code RTS/CTS Type: Configuration Format: AT [cmds] &Rn [cmds] Description: Selects RTS/CTS options Command Function &R0 CTS is off during handshake only &R1 CTS forced high EXTENDED AT COMMAND SET ABORT KEY CONTROL Type: Configuration Format: AT [cmds] %Kn [cmds] Description: Enable/disable abort key during dialing Command Function %K0 Abort key during dialing enabled %K1 abort key during dialing disabled DSR WINK Type: Immediate Format: AT [cmds] %S [cmds] Description: Returns a value which indicates line signal quality Command Function %S0 Data set ready in accordance with &S %S1 When DTR is forced high, and the modem is goes off-hook, DTR is off for 1sec. MAKE BUSY Type: Configuration Format: AT [cmds] %Bn [cmds] Description: Make busy (off-hook) if DTR lost Command Function %B0 Make busy disabled %B1 Make busy enabled if S25=0. When DTR is low, the modem goes off-hook V.23 MODE Type: Configuration Format: AT [cmds] %Fn [cmds] Description: Selects V.23 split-speed and half-duplex Command Function %F0 V.23 mode disabled %F1 75bps receive, 1200bps transmit %F2 75bps transmit, 1200bps receive SPECIAL COMMANDS DISPLAY PASSWORDS Type: Immediate Format: AT [cmds] *L [cmds] Description: Lists security passwords inserted into callback numbers (*P) EXIT FROM REMOTE CONFIGURATION Type: Configuration Format: AT [cmds] *E [cmds] Description: Exits modem from remote setting. Valid only when modem is in remote setting (*R) MNP10 - LINK NEGOTIATION Type: Configuration Format: AT [cmds] *Hn [cmds] Description: Sets the speed at which MNP10 link negotiation will occur Command Function *H0 Link will be negotiated at highest possible speed *H1 Link will be negotiated at 1200bps REMOTE SECURITY CODE Type: Configuration Format: AT [cmds] *C [cmds] Description: Executes security code feature of remote setting REMOTE SETTING Type: Immediate Format: AT [cmds] *R [cmds] Description: Remote setting is available if the function is enabled and MNP connection is enabled SECURITY FEATURES Type: Immediate Format: AT [cmds] *Pn [cmds] Description: Controls security features to prevent unauthorized access. Password is a 6-12 digit string. S(status) REGISTERS TRANSMISSION LEVEL - FAX Type: Register Format: AT [cmds] S92=n [cmds] Range: 3-15 Unit: -1 dBm Description: Sets the signal level for transmission while in fax mode TRANSMISSION LEVEL - LEASED-LINE Type Register or Configuration Format AT [cmds] S91=n [cmds] Range 3-15 Unit -1 dBm Description Sets the signal level for transmission over leased-lines